Line a room with wallpaper and you have instant decoration. From blah to daring within a matter of hours, newspaper could push boundaries outside what paint can do. It enlivens walls with textures or patterns or your choice. And as a bonus, it pushes minor imperfections in plaster and drywall, too.
However, as frequently as homeowners attempt to hang themselves, they seldom get it right, cursing their paring tiles and mismatched patterns–it’s enough to drive you up a wallsocket. Input John Gregoras, a pro newspaper hanger out of Somers, New York, with almost two years’ experience. We asked Gregoras to demonstrate a few of his very best wallpapering tips and tricks for pasting, hanging, aligning, and trimming. And, boydid we learn a lot – everything from how he plans the design to how he lines up the previous seam. With this kind of insider know-how, papering only got a great deal simpler.
Best Wallpaper Techniques Overview
Design is the secret if you are learning how to hang wallpaper. Paying attention to the sequence where the paper goes up guarantees that your pattern will stay well-matched and seem straight. John Gregoras recommends working in one direction around the room to keep the pattern consistent.
But no matter how good your technique, the routine between the first and last strip will seldom match up. For that reason, Gregoras always begins his job behind a doorway, papering out from the corner till he reaches the space over the doorway — the least conspicuous place in the room.
Frequently, the final strip of paper on a wall is not a full sheet. So another wallpapering suggestion Gregoras uses would be to always paper the corners with split sheets.
Click button on top right to enlarge illustration.
Apply Wallpaper Paste
Paint the whole room with a wall mounted primer/sizer.
Unroll the wallpaper. As you do, check for flaws and haul the paper against the edge roomgood.ru of your worktable to remove the curl.
Cut the paper into sheets 4 inches more than the height of your walls. Cut at the exact same region on the repeat so patterns on adjacent sheets will lineup.
Lay a cut sheet on the table, face down.
Suggestion: Don’t allow paste to have on the desk or it will mar the next sheet (wipe it off with a barely damp sponge when it does). Slide the paper all the way to the edge of the table to apply paste to the ends and edges.
Book the Paper
Fold the pasted back of the paper onto itself, top and bottom ends assembly in the center. Make sure that the side edges line up perfectly. Smooth the paper onto itself as far as possible without creasing the folds.
Set the paper apart to allow the paste to soak in and also the paper to unwind. Make sure you adhere to the precise booking time advocated on the background’s tag, which differs depending on its material (much more for vinyl-coated wallcoverings, less for uncoated papers).
Start in a corner near a doorway. In case the door is far from the corner, draw a reference line parallel to the door near the corner.
Overlap roughly 2 inches in the ceiling and 1/8 inch at the corner. Gently press it in place.
Unfold the bottom of the novel and let it hang. Check the dimension between the paper and the door casing or reference line. Fix the paper to keep it parallel to the doorway but still overlapping at least ⅛ inch at the corner.
Tuck and Trim the Paper
(Don’t press so hard for you to push out glue.)
Trim the excess paper in the ceilingPush a 6-inch taping knife into the joint between the ceiling and wall. Using a razor, cut over the knife to cut the excess. Work gradually. Alternate between cutting and moving the knife. Don’t slide the knife and razor together. Continue papering to a point over the door.
On the adjacent wall, then draw a plumb line (if there’s no door or window).
Hang a strip at the corner. Overlap the existing piece on the adjoining wall by 1/8 inch. Measure to the plumb line and adjust the paper to keep the distance equivalent. Smooth the newspaper. Lean in the ceiling and trim the corner.
Hang the next strip of newspaper. Unfold the surface of the book and set it on the wall. Match the routine as tightly as you can, leaving only a hair’s breadth between the sheets.
Suggestion: Push air bubbles out by sweeping the paper simpler from the middle out to the edges. Wipe off glue on the surface using a sponge.
Close the Seams
Gently press on the top of the paper to the wall. Then gently roll the seam with a seam roller to flatten down the edges. Now use the ends of your fingers to push the seam shut.
Unfold the bottom of the sheet and then complete matching and shutting the seam. Then tightly roll down the whole seam, working a full 3 inches in from the border.
Smooth the whole sheet. Continue papering the space, overlapping and trimming corners as shown in Step 5.
Suggestion: If the booked end of this strip starts to dry out before you hang it, wipe the wall with a damp sponge. This may remoisten the paste when you hang on the paper.
Cut in About Moldings
At doors and windows, allow the paper float the molding by an inch.
Carefully run the razor out of the molding corner out to the edge of the paper. Utilize the molding for a guide.
Press the cut edge tight in the joint between the molding and the wall.
Smooth down the whole sheet.
Tip: Mistakes are unavoidable once you’re learning how to hang wallpaper. Hide little cutting mistakes on darker papers by bleach the wall or the white edge of the paper with a mark that matches the paper. Some pros even colour all the paper’s borders so seams are not as evident should the paper shrink as it dries.
Paper the cover plates of electrical fixtures to make them disappear. Cut a piece of wallpaper larger than the plate. Cut out of the component of the pattern which matches the paper on the wall round the switch.
Apply paste to the plate, then lay it face down on the paper. Hold them both on the wall and then adjust the paper to match the pattern on the wall.
Hold the paper and turn the plate . Cut the corners off 1/8 inch off from the plate. Wrap the paper over the plate and then tape it on.
Cut out the change or receptacle holes using a razor. Make Xs in the screw holes. Screw the plates back to the wall.